If you have a window break in your Expedition, or perhaps the power window motor has gone out, the first thing you'll have to do to get to the broken part is remove. Mar 24, 2008. Pop the triangular plastic cover off the front top of panel (pull out at the top, then up off the door panel), there's a phillips screw underneath. Remove the courtesy light cover, there's a torx screw in there. Remove the plastic surround on the door handle and remove the bolt holding the door handle in place. For the Ford Expedition First generation, 1997, 1998, 1999, 2000, 2001, 2002 model year. Passenger compartment fuse panel. Fuse box locaton. The fuse panel is located.

I corrected this today on my 2000 F-150. Did not remove door panel as the posts that I had referenced here indicated that removal would not have helped. My vinyl 'untuck' was isolated to the top edge of the passenger side door. You will need an ALL PLASTIC PUTTY KNIFE. The one I used had a 3-4' blade, but again the blade and handle are all one piece - molded (moderately flexible) plastic. To be safe, I sanded down the outside corners of the blade, just enough to knock off the point. Working from the center of the area that needs retucking, align the blade on top of the untucked vinyl, wedging along the edges of the two panels.

Slowly & firmly press the blade down, reseating the vinyl between the two panels. Working from that spot, work to the left, repeating the process. And to the right.

You can continue process until all of the vinyl is retucked. The tool left no marring or cuts. I would guess if you needed to work a tighter radius, you may want to use a smaller blade - maybe 1'. All who has or has had this problem needs to call Ford. If Ford gets a lot calls about this they just might do something about it. 800-392-3673 Very doubtful they will do anything for a bunch of vehicles that are 6-10 years old when it comes to a 'small' problem like vinyl coming off the door panel. Mine has started doing this on the passenger's door (2004 with 220k miles).

I haven't taken it off yet but on other vehicles that I have done interior on it is about a $5 job to fix. You just have to tkae your time and use good glue.

Here is how I removed the front passenger side door panel from a 1999 Ford Expedition. The driver's side door should be the same, except for the mirror switch which needs to be unplugged. Temple Run 2 Game For Samsung Galaxy S Duos Free Download. Free Download Mv Korea Terbaru. The 1998 *might* be the same, I don't know, but this should be helpful to someone. Use a flat blade screwdriver or other suitable tool to pry out on the top of the triangular plastic panel on the top front of the door panel. The plastic holder should pull out of the door. Now pry up on both sides of the triangular panel and pull it loose.

Remove the Philips head screw you find under this panel. Pull the door latch handle, pry out the insert where the handle goes through, and remove the bolt that holds the door handle in place. Remove the door handle. Pry up on the ends of the door switch panel to remove it. Unplug the cables by pushing in on the lock tab on the side of the plug and pulling out. Remove the Philips head screw accessible through the switch panel hole. Insert a flat blade screwdriver into the slot at the bottom of the courtesy light lens and pry up and out to remove the lens.

Remove the Philips head screw behind this lens. Pull up on the door panel to remove it. Be careful of the courtesy light when removing the panel - give the light a quarter turn counter-clockwise from the rear to remove it from the door panel. Here is how I removed the front passenger side door panel from a 1999 Ford Expedition.

The driver's side door should be the same, except for the mirror switch which needs to be unplugged. The 1998 *might* be the same, I don't know, but this should be helpful to someone.Use a flat blade screwdriver or other suitable tool to pry out on the top of the triangular plastic panel on the top front of the door panel. The plastic holder should pull out of the door. Now pry up on both sides of the triangular panel and pull it loose.